Create a wireless bridge with a cheap TP- Link router. The TL- WR1. 04. 3 router from Chinese manufacturer TP- Link is one of the most capable AND inexpensive routers on the market today. And it efficiently solves a problem many people have: insufficient wireless coverage. If your home is large or prone to Wi- Fi “dead spots” where the signal is weak, you can use a wireless bridge to help overcome these problems. The bridge is nothing more than a second router that joins to your existing network, and extends its range. A bridge also increases the number of wired devices you can connect to your home network via the wired Ethernet ports on the back of it. This article assumes one of those two routers is already setup and functioning as your primary Wi- Fi router, and the other is out- of- the- box, unconfigured TP- Link TL- WR1. It will be referred to as the “bridge router” in this article. It is also recommended that you update the router to the latest firmware version from TP- Link before proceeding (3. Build 1. 10. 42. 9 Rel. Here is how you build the bridge: 1) Write down your existing wireless settings. Open up the web- based management console on your existing, primary router. Browse to the Wireless/Wireless Settings section and write down the values for channel, SSID, transmission mode, and the wireless security method and password in use. You will need these value later when you configure the bridge router. ![]() Full Bridge mode Tutorial bridging the ADSL modem. This applies to adsl modem / router users. So you have just purchased a wireless router and wish. THOMSON TG784 Wireless VoIP Multi-User Ethernet WAN & ADSL2+ Gateway Setup and User Guide. THOMSON TG784 Setup and User Guide. ![]() IP address (IPv4 or IPv6): 207.46.13.26 Browser Info: Mozilla/5.0 (compatible; bingbot/2.0; +http://www.bing.com/bingbot.htm). 10.0.0.138 is either a internal IP address or 10.0.0.138 is a private or reserved IP address with limited information on record. If you want to find out more about. How can i change my wi fi password it is tata docomo. How can i change my wi fi password it is tata docomo. 192.168.1.5.1 vivo are displayed here. Showing 192.168.1.5.1 vivo Related Routers Here Advertisements. The N300 WiFi Range Extender boosts your existing WiFi network to places out of reach of your existing WiFi. Plug it into an electrical outlet and give your WiFi a boost. Connect the bridge router. Connect the bridge router directly to your laptop with an ethernet cable plugged into any of its four LAN ports. Disable the laptop’s wifi connection, which will ensure your laptop is only talking only to the router. Power the router on, and your laptop should obtain an IP address from it. Open the Administration console. Open a web browser and go to the bridge router’s administration page at 1. Select the Wireless/Wireless Settings section. In this section, set a different Wireless Network Name (SSID) from the one used by your primary router. Then set all of the other settings on this page to match your primary router. After making these changes, you will be prompted to reboot the router, which you must do to ensure these changes take effect. After the reboot, move on to the next step. Give the bridge router a different IP. ![]() ![]() Open the router management console once again, and select the Network/LAN section. In this section, you will see that the router has a default IP address of 1. IP address as your primary router. In order to avoid an IP address conflict, change the IP address of the bridge router to 1. This time, tick the checkbox entitled “Enable WDS Bridging.” This will open a drop- down section with a number of new settings. The fastest way to do this is click the “Survey” button. This will open a new window called “AP List” which shows you all the Wi- Fi networks in range. Look for your primary router in the list by its name (SSID), and click the “Connect” link on the right. You will notice that the SSID and BSSID sections are now filled out properly. Now simply enter the wireless security values you copied from your primary router. It should look something like this, with the sections with red arrows filled in. Save the settings, and your router will reboot and join your existing Wi- Fi network. Disable DHCPSince your primary router will be handing out IP addresses on your network, you do not want the bridged router also trying to assume this role. Select the DHCP/DHCP Settings section, and disable the DHCP server. Then choose the System Tools/Reboot section, and reboot the router for the last time. Reconnect to your primary router. Disconnect the Ethernet cable from the bridge router and reenable your Wi- Fi. You should now see two possible SSID’s for you to connect to: the primary router and the new bridge router. Connect to the primary router, as you would normally do. Validate the bridge setup. You can perform a few tests to ensure your setup is configured correctly: a) Browse to the administration page on the primary router. Select the Wireless/Wireless Statistics section. In this section, you should see the MAC Address of your bridge router, and some values in the Received and Sent Packets counters, indicating the connection is working. It should look like this: Note that the MAC address of your bridge router should be printed on the bottom of the device. Browse to the 1. 92. You should be able to resolve this address and login to the adminstration page on the bridge router without issue. If both of these test pass, you should be reasonably certain your bridge is configured correctly and running. Connect to the bridge. Now reset your Wi- Fi connection to the SSID of the bridge router. You should also be able to connect a wired device to any of the LAN ports on the router and get to the Internet as well.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2017
Categories |